110 cm Acrylic RGB Car Ambient Lighting Strips

Ambient lighting acrylic strips: build your installation piece by piece

Not all cars have the same dashboard, and a pre-made kit almost always leaves an area in the shadows or a strip that is ten centimeters too long. These ambient lighting acrylic strips are sold individually, in lengths from 20 to 110 cm, with the controllers and mode button sold separately. Were you looking to complete an existing installation or replace a damaged strip without buying a whole new kit? That is exactly what this page is for.

A continuous line of light that follows the dashboard and doors

Each strip is an acrylic rod that is illuminated from one end. The result is a continuous line, with no hot spots or visible LEDs, that follows the curve of a dashboard, door trim, or console surround. It is this look, very close to the original ambient lighting of premium sedans, that sets acrylic apart from a simple adhesive strip.

Two technologies are available in each length. The RGB version displays a single color at a time across the entire strip, with smooth transitions. The multicolored version controls the LEDs one by one: several colors coexist and move in waves along the rod. It is this second version that produces the smooth rainbow effect seen in ambient lighting demonstrations.

Lengths, controllers, and button: what you can order separately

The available lengths cover all interior needs: 20 cm for a door pocket or storage cubby, 35 cm for a vent surround, 75 and 90 cm for a section of the dashboard, and 110 cm for a full-width installation. Two compact modules, listed as Horn A and Horn B, are also available for small spaces such as handles and storage compartments.

On the electronics side, the pack of five controllers allows you to extend an existing installation to new areas, and the mode button replaces a faulty control unit. These ambient lighting spare parts are exactly what you cannot find anywhere when a component fails two years after installation.

• Six lengths sold individually — 20, 35, 75, 90, and 110 cm, plus two compact modules
• RGB or addressable multicolored — single color or moving gradient on the same strip
• Controllers sold in packs of five — enough to extend an installation to several additional areas
• Mode button available separately — direct replacement for a worn control unit
• Light diffused through the material — no visible light points, a perfectly uniform line
• Rods that can be bent by hand — follow the curves of the trim without a shaping tool

Installing an acrylic strip in your car properly

The strip is not glued flat: it is inserted into the joint between two trim pieces using a plastic spatula, which holds it in place without visible adhesive and makes removal possible. The cable is then routed out through the most discreet point and run to the controller. Installing an acrylic strip requires patience, especially in the corners; allow about thirty minutes per rod the first time.

These components are designed to work with an existing ambient lighting system: before ordering, check that your controller uses the same type of connector and the same technology, RGB or addressable. If in doubt, compare the plugs on your current rods with the photos on this product page.

Can you mix RGB strips and multicolored strips?

Not on the same controller: the two technologies do not use the same electrical language, and an addressable strip plugged into an RGB output will remain off or flash erratically. However, there is nothing stopping you from having two independent systems in the same car, for example, multicolored strips on the dashboard and simple RGB in the storage compartments. The pack of five controllers is designed precisely for this type of extension.

Finding the right lighting part at Becquet Voiture

We know how frustrating it is to have to throw away an entire installation because a single rod has failed. That is why we list components individually, not just complete kits. Our French team will help you identify the length and technology that match your setup, and the catalog obviously offers complete ambient lighting kits if you are starting from scratch.

Select the length and technology you are missing, and finally complete your installation just as you had imagined.

Type: Ambient lighting acrylic strips and spare parts
Compatible brand / model: Universal, 12 V acrylic rod ambient lighting systems
Years: Depending on version
Strip lengths: 20 cm, 35 cm, 75 cm, 90 cm, 110 cm
Compact modules: Horn A and Horn B
Technologies: RGB (single color) or addressable multicolored (64 scenes)
Spare parts: Pack of 5 controllers, individual mode button
Voltage: 12 V
Material: Light-diffusing acrylic
Installation: Inserted into trim joints, no drilling required
Sold: Individually (except controller pack)