Cupra Tavascan and Volkswagen ID. UNYX 2024-2026 Mud Flaps

Cupra Tavascan mudguards: bodywork protection from gravel

This custom-fit mudguard protects the lower bodywork of your Cupra Tavascan or Volkswagen ID. UNYX from spray. A mudguard, also known as a mudflap or splash guard, is a flexible panel fitted behind the wheel that intercepts water, sand, and gravel before they reach the paintwork. Designed for 2024, 2025 and 2026 models, it perfectly matches the exact contours of the wheel arches of these two electric SUVs.

Why choose this set of mudflaps

• Specific cut: the template follows the contour of the wheel arch, without the unsightly bulging of universal models.
• Paintwork protection: fewer gravel impacts on the lower door panels and sills.
• Flexible thermoplastic: the mudflap absorbs the impact and regains its shape instead of cracking in cold weather.
• Front and rear set: all four wheels are covered, including side spray towards the doors.
• Anti-spray in wet weather: the vehicle following you receives significantly less water spray.
• Fits original mounting points: existing holes are reused, with no need to drill the bodywork.

Mudguards for everyday electric SUVs

The Cupra Tavascan and the Volkswagen ID. UNYX share the same technical base and generous wheel arches. On wet roads, an SUV of this size throws a large amount of water towards its sides: without a mudguard flap, the lower bodywork can be covered in brown streaks after just a few trips. In winter, road salt is added to the gravel and attacks the paintwork. This mudguard kit is particularly useful for daily trips on country roads, gravel paths, and parking lots under renovation.

Technical specifications

Type: custom-fit mudguard, set of front and rear mudflaps. Material: UV and frost-resistant flexible thermoplastic. Colour: matte black, discreet on all bodywork colours. Target vehicles: Cupra Tavascan and Volkswagen ID. UNYX, 2024 to 2026. Fastening: screws and clips supplied, using the original mounting points. The front and rear mudflaps have different templates: identify them before fitting. Operating temperature range: -30°C to +80°C.

Installation and maintenance

Allow 30 to 45 minutes for the entire vehicle, with a ratchet and Torx key. Turn the wheel to its maximum to clear access, clean the edge of the wheel arch, position the mudflap and thread the screws without tightening, then adjust the alignment before locking. Never force a screw that is not properly threaded: the plastic inserts in the wheel arch are fragile. Rinsing with clean water after a winter trip is sufficient for maintenance. Compatibility is indicative and should be checked according to the trim level before installation.

Frequently asked questions

Do I need to drill the bodywork?
No. The original mounting points of the wheel arch are reused. Removal is reversible and leaves no trace.

Do the mudflaps rub when steering?
No, the template respects the original travel. Careful alignment during fitting prevents any contact with the tyre.

Do they increase fuel consumption?
The aerodynamic effect is marginal at legal speeds. The gain in cleanliness and paintwork protection more than compensates for it.

Do the Tavascan and ID. UNYX have the same wheel arches?
Yes, both models share the same platform and wing cut, hence a common template.

Are the mudflaps resistant to high-pressure washing?
Yes, provided you keep a distance of about thirty centimetres and do not direct the jet under the mudflap.

Protect the paintwork of your Tavascan from the very first winter: fit these mudflaps in less than an hour and forget about gravel impacts.

Type: Custom-fit mudguard, front and rear mudflaps
Compatible brand: Cupra Tavascan, Volkswagen ID. UNYX
Years: 2024, 2025, 2026
Material: UV-resistant flexible thermoplastic
Colour: Matte black
Main function: Anti-gravel and anti-splash protection
Installation: On original mounting points, screws supplied
Condition: 100% New