Jeep Wrangler JL Mud Flaps — Bodywork Protection from the Very First Trail
This mud flap set for the 2024–2026 Jeep Wrangler JL Rubicon stops mud, gravel, and salt from reaching the rocker panels and running boards. The 4-piece kit covers the front and rear wheel wells, with a cut specifically designed for the Rubicon's wide fenders. Hardware and mounting template included.
Why Mud Flaps on an Off-Road 4x4?
- Complete 4-piece kit: two front mud flaps, two rear mud flaps, plus hardware and a drilling template.
- Knobby tires = heavy spray: the large tread blocks of an off-road tire throw rocks much further than a street tire.
- Cold-resistant flexible plastic: the mud flap bends over an obstacle instead of breaking, even in sub-zero temperatures.
- Textured black finish: the same matte texture as the Wrangler JL's factory fender flares.
- Cutout designed for Rubicon fenders: the shape follows the edge of the fender flare without gaps or loose sections.
- Protects the running boards and lower door panels, the two areas that rust first on a 4x4 used in winter.
What Is a Mud Flap for on a Wrangler?
A mud flap or mudguard is a flexible screen mounted behind the wheel to catch what the tire throws up. On a Jeep Wrangler, the issue goes beyond aesthetics. Off-road tires with large tread blocks trap gravel and mud in their grooves and release them at high speed: without a screen, the spray hits the lower door, running board, and edge of the rear bumper. On roads treated with salt in winter, every paint chip becomes a corrosion point. The mud flap also limits what you throw at the vehicle following or trailing you on the trail. It does not restrict off-road clearance: the part is flexible, it gives way over an obstacle and regains its shape.
Technical Specifications
Type: Front and rear mud flaps. Quantity: 4 pieces. Vehicle: Jeep Wrangler JL Rubicon, model years 2024 to 2026. Material: UV- and cold-resistant flexible plastic. Color: textured black. Mounting: self-tapping screws and washers included, drilling template included. Installation: On the fender flare, without removing bodywork. Condition: 100% new. Compatibility should be checked according to the trim before installation.
Installation and Maintenance
Allow 40 minutes to 1 hour for all four. Turn the wheel fully on the side being worked on to clear access: there is no need to lift the vehicle. Clean and dry the edge of the fender flare before positioning the part. Position the included template, mark the points, then drill to the indicated diameter. One tip to prevent rust: apply a dab of rust-proofing paint or wax in each hole before screwing. Tighten without forcing—an overtightened screw deforms the mud flap, causing it to rattle at cruising speed. Finally, check the full wheel articulation. Maintenance: spray with water during every wash to clear out dried mud trapped behind the mud flap, and check the tightness after every off-road outing.
Frequently Asked Questions
Will this kit fit a non-Rubicon Wrangler JL?
The cutout is designed for Rubicon fender flares. On other JL trims, compare the shape of the fender edge before ordering.
Do I need to drill to install the mud flaps?
Yes, installation is done with self-tapping screws using the included template. Treat the holes against corrosion before screwing.
Do the mud flaps interfere with off-road clearance?
No. The flexible plastic gives way over an obstacle and then regains its shape. The bottom clearance angle is not altered.
Are they suitable for oversized tires?
Check the full wheel articulation after installation. With a lift kit and wide tires, a slight trim may be necessary.
Can they withstand pressure washing?
Yes, by keeping the wand at least 30 cm away and avoiding prolonged pressure on the screw area.
Protect your lower bodywork on your next outing: complete 4-piece kit, hardware, and template included.
Type: Front and rear mud flaps
Quantity: 4 pieces
Vehicle: Jeep Wrangler JL Rubicon, 2024–2026
Material: Textured black flexible plastic
Mounting: Self-tapping screws and template included
Installation: On fender flare
Installation time: 40 min to 1 hr
Condition: 100% New
Customer reviews
Reviews from our customers
Ordered this product from us? Leave a review and add your photos: it helps other enthusiasts choose.
