SEAMETAL Phone Tablet Holder for Car Rear Seat

SEAMETAL Phone and Tablet Mount: the reinforced model that no longer wobbles on rough roads

The flaw of cheap rear screen mounts can be summed up in one word: vibration. At the first set of highway expansion joints, the tablet wobbles, the image becomes unreadable, and passengers end up taking it back in their hands. SEAMETAL has addressed the problem with rigidity: thickened sections, reinforced locking joints, and oversized contact pads. This rear seat car tablet mount holds the screen stable where hollow models start to dance.

The SEAMETAL graphite gray finish, closer to the original equipment

The dark gray anodized treatment and softened edges give this mount the appearance of a factory-installed part rather than an added accessory. Seen from the back, it blends in with the backrest rods instead of creating that shiny black mass that stands out on generic models. It's a detail, but it's exactly the kind of detail that separates a neat interior from an interior cluttered with gadgets.

The cradle itself remains understated: two wide jaws, an open back for the tablet's heat dissipation, and cutouts for cables. A rear seat screen mount should be forgotten when no one is using it: this one folds against the backrest in a few seconds.

Telescopic arm and anti-wobble locking: the SEAMETAL design in detail

The arm slides into a sleeve guided along its entire length, not on a simple pin: this is what eliminates the lateral play responsible for wobbling. The ball joints lock with a tapered clamping mechanism, a more durable solution than plastic notches that eventually give out. As a result, the chosen position really holds, even with a 12.9-inch tablet weighing over six hundred grams cantilevered.

The reception range covers 4 to 12.9 inches, which goes from the large smartphone to the iPad Pro format. The silicone inner pads hug thick cases as well as bare tablets, without marking the edges. This car phone and tablet mount accepts both portrait and landscape mode.

• Reinforced anti-vibration structure — the screen remains readable on degraded surfaces and highway expansion joints.
• Compatible with 4 to 12.9 inches — from smartphone to large format, including thick cases.
• Guided telescopic arm — the screen moves toward the passenger without lateral play.
• Ball joint locking with tapered clamping — the adjustment does not loosen over the miles.
• Graphite anodized finish — discreet on dark upholstery, without shiny plastic.

Fixing the SEAMETAL on the backrest of your front seat

The two clamps open by hand and come to grip the metal rods of the backrest; the tightening is done by knob, without any tools and without drilling. Allow two minutes for the installation of a tablet mount on a car seat, just as much to remove it. Before ordering, check that your front seats have exposed rods: solid backrests, bucket seats, and some interiors equipped with original screens do not allow this type of fixation.

Can this mount stay in place permanently in the car?

Yes, provided you fold it back when the rear seat is occupied without a screen, and remove the tablet as soon as you leave the vehicle — for safety as well as to not expose the device to prying eyes in a parking lot. The mount itself handles life on board very well: the anodization is not affected by temperature fluctuations or humidity, and the silicone pads do not harden like low-end foam. This is one of the benefits of a car tablet mount made of alloy rather than injected plastic.

Comfort in the back, a Becquet Voiture specialty

We spend as much time looking for the right interior accessories as we do selecting our style pieces, and we systematically discard models whose mechanism fails after a few months. Our car phone mount section covers both the front and back of the vehicle, with advice in French on the compatibility of your seats.

Switch to the SEAMETAL and offer your passengers a truly stable screen, regardless of the road conditions.

Type: Phone and tablet mount for front seat backrest
Brand: SEAMETAL
Device compatibility: 4 to 12.9 inches, thick cases accepted
Fixation: Clamps with knob on metal backrest rods
Arm: Guided telescopic, ball joints with tapered clamping
Orientation: Portrait and landscape
Material: Anodized alloy and silicone pads
Finish: Graphite gray
Packaging: 1 piece
Installation: Tool-free, no drilling, reversible
Vehicle compatibility: Universal, seats with exposed rods required, to be checked before installation
Condition: 100% New